Programmable Measuring Instruments Series 8100

Modular System Series 8000

Options

Accessories

	Adapter

	Test Leads

	Probes

	Interface Cables

	Sensors and Probes

	Test Adapters

	Accessories for Spectrum Analyzers

	General Accessories

Catalog

Probes

HZ56-2 *

AC/DC Current Clamps

This AC/DC Current Probe is used to measure currents from 1mA to 30 A over a broad frequency range. The measurement principle is based on the Hall Effect that registers the magnetic field generated by the current flow. Even for complex waveforms a high degree of measurement accuracy is achieved. The output voltage is proportional to the measured current and well suited to be displayed on an oscilloscope. The current probe complies with the safety standards defined in IEC/EN 61010.

Measurement range:	±30 A_DC / 20 A_AC
Accuracy:	±1% ±2mA
Frequency range:	DC to 100 kHz
Resolution:	1 mA
Output voltage:	100 mV/A
Load impedance:	> 100 kΩ
Voltage stability:	3.7 kV / 50 Hz / 1 minute
Connection:	BNC-Cable, 2 m

* Product discontinued; Successor: HZO50

Manuals (1)

HZO40

Differential Probe 10:1

Technical specifications at 23 °C ±2 °C

Bandwidth:	200 MHz
Attenuation ratio:	10:1
Rise time (10…90%):	1.75 ns
Gain accuracy	±1%
Max. Input Voltage per Input:	±60 V
Max. Differential Input Voltage (DC + peak AC):	±20 V
Max. Common Mode Input Voltage:	±60 V
Input impedance
Between Inputs:	1 MΩ II 3.5 pF
Each Input to Ground:	500 kΩ II 7 pF
Output Voltage (into 50 Ω):	±2 V
Offset (typical)	±2 mV
CMRR (typical):	-80 dB at 60 Hz -50 dB at 10 MHz
Battery operation:	9 V battery 6LR61
Battery life (typical):	7.5 h
Input for an external power supply:	USB Power adapter cable (5…9 V_DC/200 mA)

Datasheets (4)	Manuals (1)
Professional articles (5)

HZO41

Differential Probes 10:1

Technical specifications at 23 °C ±2 °C

Bandwidth:	800 MHz
Attenuation ratio:	10:1
Rise time (10…90 %):	437 ps
Gain accuracy	±2 %
Max. Input Voltage per Input:	±40 V
Max. Differential Input Voltage (DC + peak AC):	±15 V
Max. Common Mode Input Voltage:	±30 V
Input impedance
Between Inputs:	200 kΩ II 1 pF
Each Input to Ground:	100 kΩ II 2 pF
Output Voltage (into 50 Ω):	±1.5 V
Offset (typical)	±5 mV
CMRR (typical):	-60 dB at 60 Hz -15 dB at 500 MHz
Battery operation:	9 V battery 6LR61
Battery life (typical):	4.5 h
Input for an external power supply:	USB Power adapter cable (5…9 V_DC/300 mA)

Datasheets (4)

Manuals (1)

HZO50

AC/DC Current Probe 30 A

This AC/DC current probe is used to measure currents from 1mA to 30 A over a broad frequency range. The measurement principle is based on the Hall Effect that registers the magnetic field generated by the current flow. Even for complex waveforms a high degree of measurement accuracy is achieved. The output voltage is proportional to the measured current and well suited to be displayed on an oscilloscope. The current probe complies with the safety standards defined in IEC/EN 61010.

Specifications
Measurement range:	± 20 A_rms/30 A_p
Accuracy:	± 1% from measurement value ± 2 mA
Bandwidth:	DC…100 kHz (0,5 dB)
Resolution:	± 1 mA
Output voltage:	100 mV/A
Load impedance:	› 100 kΩ II ≤ 100 pF
Max. Voltage:	300 V_rms (AC or DC)
Output cable/Connector:	2m (50 Ω)/BNC
Measuring category:	CAT III

Datasheets (4)

Manuals (1)

HZO51

AC/DC Current Probe 100/1000 A

This AC/DC current probe is used to measure currents from 100mA to 1000A over a broad frequency range. The measurement principle is based on the Hall Effect that registers the magnetic field generated by the current flow. Even for complex waveforms a high degree of measurement accuracy is achieved. The output voltage is proportional to the measured current and well suited to be displayed on an oscilloscope. The current probe complies with the safety standards defined in IEC/EN 61010.Specifications

Specifications
Measurement range:	±100 A_rms/1000 A_rms
Accuracy:	±1% from measurement value ±0.1 A/±0.5 A
Bandwidth:	DC…20 kHz
Resolution:	±100 mA/±500 mA
Output Voltage:	10 mV/A/1 mV/A
Load impedance:	>100 kΩ II ≤100 pF
Max. Voltage:	300 V_rms (AC or DC)
Output cable/Connector:	2 m (50 Ω)/BNC
Measuring category:	CAT III

Datasheets (4)

Manuals (1)

HZ350

Probe 10:1

Attenuation ratio:	10:1
Bandwidth:	350 MHz
Rise time:	<1.0 ns
Input impedance:	10 MΩ II 12 pF
Max. Voltage:	400 V (DC + peak AC)
LF compensation:	1 Trimmer
RF compensation:	2 Trimmer
Cable length:	1.2 m
Probe factor identification:	automatically after connection
Measuring category:	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZ355

Probe 10:1

Attenuation ratio:	10:1
Bandwidth:	500 MHz
Rise time:	<700 ps
Input impedance:	10 MΩ II 9.5 pF
Max. Voltage:	400 V (DC + peak AC)
LF compensation:	1 Trimmer
RF compensation:	2 Trimmer
Cable length:	1.3 m
Probe factor identification:	automatically after connection
Measuring category:	CAT I

Datasheets (4)	Manuals (1)
Professional articles (8)	Knowledge Base (1)

HZ200

Probe 10:1

Attenuation ratio:	10:1
Bandwidth:	250 MHz
Rise time:	<1.4 ns
Input impedance:	10 MΩ II 12 pF
Max. Voltage:	400 V (DC + peak AC)
LF compensation:	1 Trimmer
RF compensation:	2 Trimmer
Cable length:	1.2 m
Probe factor identification:	automatically after connection
Measuring category:	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZ51

Probe 10:1

Attenuation ratio	10:1
Bandwidth	150 MHz
Rise time	<2.4 ns
Input impedance	10 MΩ II 12 pF
Max. Voltage	600 V (DC + peak AC)
LF compensation:	1 Trimmer
RF compensation: 1 Trimmer
Cable length	1.2 m
Measuring category	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZ52

Probe 10:1

Attenuation ratio	10:1
Bandwidth	250 MHz
Rise time	<1.4 ns
Input impedance	10 MΩ II 10 pF
Max. Voltage	600 V (DC + peak AC)
LF compensation	1 Trimmer
RF compensation	2 Trimmer
Cable length	1.2 m
Measuring category	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZ53

Probe 100:1

Attenuation ratio	100:1
Bandwidth	100 MHz
Rise time	<3.5 ns
Input impedance	100 MΩ II 4.5 pF
Max. Voltage	1200 V (DC + peak AC)
LF compensation	1 Trimmer
Cable length	1.2 m
Measuring category	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZ154

Probe 1:1 / 10:1

Attenuation ratio	1:1
Switchable	10:1
Bandwidth	10/100 MHz
Rise time	‹ 35/3.5 ns
Input impedance	1/10 MΩ II 82/12 pF
Max. voltage	(10:1) 600 V (DC + peak AC)
LF compensation	1 Trimmer at 10:1
RF compensation	2 Trimmer at 10:1
Cable length	1.2 m
Measuring category	CAT I

Datasheets (4)	Manuals (1)
Knowledge Base (1)

HZO20

Probe 1000:1

Attenuation ratio:	1000:1
Bandwidth:	400 MHz
Rise time:	‹ 900 ps
Input impedance:	50 MΩ II 7.5 pF
Max. Voltage:	1000 V_rms
LF compensation:	1 Trimmer
RF compensation:	1 Trimmer
Cable length:	1.3 m
Probe factor identification:	automatically after connection
Measuring category:	CAT II

Datasheets (4)

Manuals (1)

HZO30

Active Probe 10:1

Attenuation ratio:	10:1
Bandwidth:	1GHz
Rise time:	600 ps
Input impedance:	1 MΩ II 0.9 pF
Max. Input voltage:	20 V
Input Dynamic Range:	± 8 V
Cable length:	1.3 m
Oscilloscope Input Coupling:	50 Ω
External Power Supply	included

Datasheets (4)	Manuals (1)
Professional articles (7)

HZO10

Probe 10:1

Attenuation ratio:	10:1
Bandwidth:	250 MHz
Rise time:	<1.4 ns
Input impedance:	10 MΩ II 15 pF
Max. Voltage:	400 V (DC + peak AC)
LF compensation:	1 Trimmer
RF compensation:	2 Trimmers
Cable length:	1.2 m
Probe factor identification:	automatically after plugging
Measuring category:	CAT I

Datasheets (4)

Manuals (1)

HZ100

Differential Probe 20:1 / 200:1

Technical specifications at 23 °C ± 2 °C

Differential input voltage (DC + peak AC) max.:	±700 V
Max. input voltage per input:	600 V_rms
Attenuation ratio:	20:1
Selectable:	200:1
Bandwidth:	30/40 MHz
Rise time:	12/9 ns
Input impedance:	8 MΩ II 1.2 pF
Output impedance:	50 Ω
Max. output Voltage:	±3.5 V at 1 MΩ
Max. noise:	2 mV
Accuracy after 1 min:	±3% (18…30 °C)
Common mode rejection DC/AC 1 MHz:	70 dB/>50 dB
Inputs (CAT III):	2 safety connectors
Input leads:	2 test leads 50 cm with spring hooks
Battery operation:	9 V battery 6LR61
Input for an external power supply:	12…14 V_dc/30 mA

Datasheets (4)

Manuals (2)

HZ109

Differential Probe 1:1/10:1

Technical specifications at 23 °C ± 2 °C

Differential input voltage (DC + peak AC) max.:	±3,5 V/35 V
Max. input voltage per input:	100 V_rms
Attenuation ratio:	1:1
Selectable:	10:1
Bandwidth:	30/40 MHz
Rise time:	12/9 ns
Input impedance:	8 MΩ II 1.2 pF
Output impedance:	50 Ω
Max. output Voltage:	±3.5V at 1 MΩ
Max. background noise at x1:	<8 mV_rms
at x10:	<2 mV_rms
Accuracy after 1 min:	±3 % (18…30 °C)
Common mode rejection DC/AC 1 MHz:	70 dB/>50 dB
Inputs (CAT III):	2 safety connectors
Input leads:	2 test leads 50 cm with spring hooks
Battery operation:	9 V battery 6LR61
Input for an external power supply:	12…14 V_dc/30 mA

Datasheets (4)

Manuals (2)

HZ115

Differential Probe 100:1/1000:1

Technical specifications at 23 °C ± 2 °C

Differential input voltage (AC_rms):	1000 V
(DC + peak AC) max.:	±1400 V*)
Max. input voltage per input:	±1400 V*)
Attenuation ratio:	100:1
Selectable:	1000:1
Bandwidth:	20/30 MHz
Rise time:	17/12 ns
Input impedance:	60 MΩ II 1.5 pF
Output impedance:	50 Ω
Max. output Voltage:	±1.5 V at 1 MΩ
Max. background noise:	2 mV
Accuracy after 1min:	±3 % (18…30 °C)
Common mode rejection DC/AC 1 MHz:	70 dB/>50 dB
Inputs (CAT III):	2 safety connectors
Input leads:	2 test leads 75 cm with safety test clips
Battery operation:	9 V battery 6LR61
Input for an external power supply:	12…14 V_dc/30 mA

*) due to test clip 1000 V CAT III

Datasheets (4)

Manuals (3)

HAMEG summer promotion: Great offers until October 2013 +++ Spectrum Analyzers HMS1000, HMS1010 and HMS1000E now with extended frequency range of 1.6GHz… [more…] +++ Embedded World: HAMEG introduces new HMO3000 series of oscilloscopes with up to 500MHz bandwidth. +++