HAMEG Instruments GmbH
Home | Products | Blog | Dealer | Service & Support | Company | Contact    
Warranty & Repair
HAMEG Calibration
Downloads
Knowledge Base
General
Oscilloscopes
Spectrum Analyzer
Power Supplies
Programmable Measuring Instruments Series 8100
Modular System Series HM8000
Accessories
Blog
Dealer's Area
ImprimirImprimir

Knowledge Base

KB > Programmable Measuring Instruments Series 8100 > HM8118 
Go to category:
Go to article ID:
Full-text search:
Qué buscar:
 

Búsqueda avanzada

Categories HM8118:
folderHM8118: Basic knowledge
folderHM8118: Example to determine the accuracy
folderHM8118: Test frequency in 69 steps (20Hz...200kHz)
folderHM8118: Using of the HZ186 Transformer Test Cable
folderHM8118: LabView driver available?
folderHM8118: Measurement of a resistor
folderHM8118: Measuring inductance and resistance values
folderHM8118: Display of test signal voltage Vm and current Im levels
folderHM8118: Transformer measurement with incorrect results
folderHM8118: OPEN / SHORT calibration via interface
folderHO118: Tolerance of sorting components
articleHM8118: Basic knowledge
In general, the LCR bridge HM8118 (as well as all other LCR meter in this price segment) is determined complex quantities, that means the impedance and phase angle ...
articleHM8118: Example to determine the accuracy
articleHM8118: Test frequency in 69 steps (20Hz...200kHz)
The LCR Bridge HM8118 features a frequency range of 20 Hz to 200 kHz in 69 steps:    ...
articleHM8118: Using of the HZ186 Transformer Test Cable
For transformer measurement we recommend to use the HAMEG HZ186 accessory.   Please connect the clamps like described below (from left to right):   - ...
articleHM8118: LabView driver available?
HAMEG does not provide a LabView library for the LCR bridge HM8118.   The remote control commands of the manual are based on the SCPI standard. You can find ...
articleHM8118: Measurement of a resistor
The resistance measurement of the HM8118 always works with the method voltage application (AC) and measuring the resulting current. The only difference from L or C ...
articleHM8118: Measuring inductance and resistance values
To measure a simple resistor or a inductance you need to switch on the L-R mode on the keypad of the HM8118. If you do so, you can read out the resistor and ...
articleHM8118: Display of test signal voltage Vm and current Im levels
You can calculate mathematically the voltage range as well as the current range, but the HM8118 provides the possibility to display this two values during the ...
articleHM8118: Transformer measurement with incorrect results
The different measurement results are depending on the loss of the iron core as well as the unknown state of the pre-magnetized core.   The coil, which is to ...
articleHM8118: OPEN / SHORT calibration via interface
From firmware update version 1.32 the interface commands for OPEN / SHORT calibration are available:   - CROP (OPEN calibration) - CRSH (SHORT ...
articleHO118: Tolerance of sorting components
The HO118 option is able to handle any tolerances, even assymetrical (for example -5% and +20%).   The tolerances can be entered with the keypad or via ...
articleback to  Programmable Measuring Instruments Series 8100
 
 
Embedded World: HAMEG introduces new HMO3000 series of oscilloscopes with up to 500MHz bandwidth. +++ Spectrum Analyzers HMS1000, HMS1010 and HMS1000E now with extended frequency range of 1.6GHz… [more…] +++ HAMEG summer promotion: Great offers until October 2013 +++ 
© 2013 HAMEG Instruments GmbH | Edita | Condiciones generales